The honest answer to unvented cylinder pricing is that the cylinder is the small part; the cupboard, the pipework and what is coming out first decide the bill.
The Essentials
- Cylinder capacity, location and access are the three biggest cost drivers on any unvented cylinder installation.
- Like-for-like hot water cylinder replacement costs less than converting from an old vented tank and loft feeds.
- The price should include safety kit, discharge pipework, controls wiring, commissioning and the Building Regulations paperwork.
- Many faults are repairs, not replacements, so a failed valve, vessel or immersion heater is a fraction of the cost.
- Cylinders fitted by the team come with a guarantee of up to ten years where the annual service is maintained.
Heating Services Ltd was established in 2008, and David heads a team of locally based Gas Safe engineers rather than subcontractors. If you need unvented cylinders in Morden, we cover the whole area, and there are many five-star reviews on the widget on this page.
Tell us what is in the cupboard now and we will price the job properly.

How much does it cost to fit an unvented cylinder?
Fitting an unvented cylinder is usually a full day or two of work, and the price depends on the cylinder size, where it is going, the pipework and controls needed, and whether an old vented tank and loft feeds are being stripped out first. Every quote is priced on the actual job.
Send us a photo of your existing cylinder and we will come out, check your mains flow rate and give you a firm price for the work.

The things that move the price up or down
After more than a few hundred cylinder swaps, the pattern is always the same. The cylinder itself is only part of the bill. Capacity matters, because a 120 litre unit for a small flat is a different animal to a 300 litre cylinder feeding three bathrooms. Location matters more than people expect: an airing cupboard on the first floor with a wall handy for the discharge pipe is a straightforward day, while a loft or a garage conversion means longer runs, more insulation and more time.
Then there is what you are replacing. A like-for-like unvented cylinder replacement, same footprint, same pipe centres, is the cheapest version of this job. Coming off an old gravity system is a bigger piece of work, because the cold water storage tank and feed pipes come out, the cold main has to be re-routed to feed the cylinder, and the boiler controls often need re-wiring for a two-port or three-port valve. Add a new expansion vessel, tundish and discharge route to a safe outside point and you can see where the hours go.
We cover the whole area, and the quote is always worked out from what is actually in the cupboard rather than a generic figure. Access, water pressure and flow rate are checked before anything is ordered, because an unvented system only performs as well as the incoming main allows.

What is included when the team installs one
A proper hot water cylinder installation is not just the cylinder standing in place. The price covers isolating and draining down, removing the old unit and any redundant tank, fitting the new cylinder with its safety kit, running or upgrading the cold main connection, setting the pressure reducing valve and expansion vessel, taking the discharge pipe to a safe termination, fitting and wiring the immersion heater and controls, then commissioning, balancing and testing the whole thing.
Building Regulations treat unvented hot water as notifiable work, so the installation is carried out by an engineer holding the relevant unvented qualification and the paperwork is left with you. Where the cylinder is heated by a gas boiler, the engineers on the team are Gas Safe registered, which is the register the Health and Safety Executive points households to for gas work. We cover the whole area with the same standard of workmanship.
- Removal and safe disposal of the old cylinder, tank and pipework
- New cylinder, expansion vessel, PRV, tundish and discharge arrangement
- Cold main upgrade or re-route where flow rate needs it
- Immersion heater, cylinder stat, zone valve and control wiring
- Commissioning, pressure testing and handover with the certificate
Send us a photo of your existing cylinder and we will come out, check your mains flow rate and give you a firm price for the work.

Repair, service or replace, and what that costs you
Not every cylinder needs replacing. Plenty of the calls that come in turn out to be a discharging expansion relief valve, a vessel that has lost its air charge, a failed immersion heater or element, a sticking motorised valve or a cylinder thermostat that has given up. Those are repairs, not installations, and they are far cheaper than a new cylinder. A hot water cylinder repair on the first visit is the usual outcome, and same-day attendance is what this firm has built its name on, because there are local engineers spread across the coverage area rather than one van crossing the county.
An annual service on an unvented cylinder is money well spent. Recharging the vessel, checking the relief valves and testing the discharge takes an hour or so and stops the failures that end in a flooded cupboard. Where a cylinder is corroded, leaking from the coil or well past its guarantee period, replacement is the honest answer and the team will say so. Our hot water cylinder installation services and repair work run side by side, so the same engineer can quote for both on the one visit.
.jpeg)
Why an unvented cylinder is worth the outlay
Mains pressure hot water at every tap, no loft tank, no pump, no airlocks and showers that actually feel like showers. That is what people are buying. On top of that, a well specified unvented cylinder with a decent coil recovers quickly, works happily with a system boiler or a solar coil, and frees up loft space. Cylinders installed by the team carry a guarantee of up to ten years subject to the annual service being kept up.
Heating Services Ltd was established in 2008 and David, who has over 21 years in the trade, heads a team of locally based Gas Safe engineers working across Surrey, London and the South East. Never subcontractors. That local coverage is the reason quotes get done quickly and breakdowns get attended fast, and it is why the same team can be trusted with the install, the service and any repair afterwards.
Send us a photo of your existing cylinder and we will come out, check your mains flow rate and give you a firm price for the work.


.jpeg)