Heating Services Ltd has worked on heating and hot water systems since 2008, and David has over 21 years in the trade. With unvented cylinders, that experience shows in the details: a relief valve that is letting by, an expansion vessel that has quietly lost its charge, a discharge pipe that has to fall correctly. Our engineers bring that experience to homes across Thamesmead.
Summary
- How a cylinder installation is staged so the house keeps running
- Which faults show up at the tundish and what causes them
- The six checks covered in every annual cylinder service
- Three safe steps to take if hot water runs from the tundish
We are Gas Safe registered and use our own locally based engineers, the same team behind underfloor heating installation in Thamesmead, so the people who quote are the people who do the work.
Ask Heating Services Ltd for a clear written quote in Thamesmead today, before a dripping tundish turns into a flooded cupboard.
.jpeg)
Unvented Hot Water Cylinder Services
We install, service and repair unvented hot water cylinders across Thamesmead and the surrounding SE28 area. An unvented cylinder is fed straight from the cold mains. It stores that water under pressure and heats it through a boiler coil, an immersion heater, or both. There is no cold water tank in the loft. And every tap and shower gets mains pressure.
That pressure is why the safety controls matter so much. A sound installation carries a pressure reducing valve, an expansion vessel, a temperature and pressure relief valve and a discharge pipe running through a tundish to a safe point. If one of those is wrong, you get a leak, a scald risk or a cylinder that dumps water. We fit and check all of them on every job.
The upheaval often worries people more than the cylinder does. So this is how a hot water cylinder installation is staged.
Survey and sizing
We start in your home. Our engineer measures the incoming mains pressure and flow, counts the bathrooms and outlets, and asks how many people use hot water at peak times. We check your boiler is compatible, decide where the cylinder will sit and plan the discharge pipe route. You then get a clear written quote. No surprises later.
Preparing the space
Before anything is drained, we cover the floors and the route from the door to the airing cupboard. We tell you which taps will be off and when, so you can plan showers and the kettle around it. The old cylinder is drained down and disconnected, and any redundant loft tank and pipework is isolated. The rest of the house carries on as normal. Work stays in the cupboard and along the pipe run.
Fitting the cylinder and its controls
The new stainless steel cylinder goes in first. The inlet control group follows, with its strainer, pressure reducing valve and check valve. Then come the expansion vessel, the relief valves and the tundish. The discharge pipe is laid in copper at a steady fall to its termination point. Last, the thermostat, the immersion heater and the boiler controls are wired in.
Commissioning and handover
We fill and purge the system, inspect every joint under pressure, operate the relief valves by hand and set the cylinder thermostat. Then we run each tap and shower. Your paperwork is completed to current building regulations, and the engineer shows you the tundish and explains what a drip there means. The old cylinder and the packaging leave with us. Installations are backed by a guarantee of up to 10 years.
Ask Heating Services Ltd for a written quote on Unvented Cylinders in Thamesmead, from our own locally based Gas Safe engineers.

Fault Finding and Repair of Unvented Systems in Thamesmead
Unvented faults show up in a handful of ways, and each one points to a different part of the system. Our engineers test before they replace anything. They gauge the expansion vessel charge, measure the inlet pressure after the reducing valve, and check the thermostat and immersion element with a meter.
- Water at the tundish: usually a flat expansion vessel or a relief valve that has started to let by.
- Weak flow or falling pressure: often a blocked inlet strainer or a failing pressure reducing valve.
- No hot water: a failed immersion element, a faulty cylinder thermostat, a stuck motorised valve or a fault on the boiler side.
- Banging or hissing during heating: often a sign the expansion vessel can no longer absorb the extra volume.
- Damp around the base: a weeping joint or, on older units, the cylinder itself.
Hot water cylinder repair is core work for us, alongside installation. Our engineers are spread across the area, so once you report a fault there is usually someone who can reach you that same day.
Some cylinders are past saving. If the vessel itself is leaking or corroded, we will tell you plainly and quote for hot water cylinder replacement, staged as carefully as any new installation. If a valve or the vessel is the problem, we repair that part and leave the rest alone.
.jpeg)
Benefits of an Unvented Hot Water Cylinder
The case for an unvented cylinder comes down to pressure and space. The water arrives at mains pressure instead of relying on a tank above, so the gains are practical, and you notice them on the first morning.
- Strong showers without a separate pump, as long as the incoming mains pressure and flow are adequate.
- Several taps and showers running at once with little drop in pressure.
- No cold water storage tank in the loft to insulate, inspect or maintain.
- Stainless steel construction that resists corrosion inside the vessel.
- Flexible siting, because the cylinder does not depend on height for its pressure.
These points matter most where demand is heavy. We also support hotels and hospitality premises, where many rooms draw hot water at the same moment and a pressure drop is noticed quickly. In a family home in Thamesmead, it means two showers running at once. No queue.

Cylinder Servicing and Annual Maintenance
An unvented cylinder is a pressurised vessel, and its safety devices only work if they are kept in order. Expansion vessels lose their charge slowly. Strainers silt up. Relief valves that are never operated can stick. A yearly service catches each of these before it becomes water on the floor, and many cylinder makers ask for one to keep their warranty valid.
Every annual service covers the same checks:
- Expansion vessel pre-charge tested and topped up to the cylinder's specification.
- Inlet strainer removed and cleaned, and pressure reducing valve output checked.
- Temperature and pressure relief valves operated by hand to confirm they open and reseat.
- Tundish and discharge pipe inspected for flow, fall and any sign of past discharge.
- Cylinder thermostat, high-limit cut-out and immersion heater tested.
- Visible joints and valves checked for weeping or corrosion.
Servicing is a light job. Water is isolated only while the inlet group is open. Everything else happens inside the cupboard with your supply on, and the engineer tells you what was found before leaving.

Emergency Callouts and Fast Response
Some faults cannot wait. Hot water running continuously from the tundish means a control has failed and the cylinder is protecting itself. Until we arrive, take these three steps in order:
- Switch off the boiler and the immersion heater.
- Close the cold mains stop valve feeding the cylinder.
- Keep clear of the discharge point, because the water can be scalding.
Then call us. David heads a team of our own locally based Gas Safe engineers, not subcontractors, working across Surrey, London and the South East. If you need an unvented cylinder engineer near you in Thamesmead, one of the team is rarely far away, and urgent faults are usually seen the same day.
The engineer who comes out will explain what failed and why, make the system safe and repair it on the spot where the parts allow. If the cylinder is past repair, you get a clear written quote for a replacement, with the installation planned around your home. Tell us what is happening at the tundish and we will take it from there.
Ask Heating Services Ltd for a written quote on Unvented Cylinders in Thamesmead, from our own locally based Gas Safe engineers.


