Radiator Installations & Repair in Hammersmith

Heating Services Ltd was established in 2008, and David, who heads the team, has over 21 years in the trade. For Radiator Installations & Repair in Hammersmith, that length of time means our engineers have seen most of what a central heating circuit can do: valves that seize, panels that rot from the inside, and systems that never balanced properly in the first place.

We are a Gas Safe registered firm, established in 2008, working with our own locally based engineers rather than subcontractors. The same team also handles boiler repairs for Hammersmith households, so the radiators and the boiler feeding them are looked after together.

Tell Heating Services Ltd what your radiators are doing and get a clear written quote for your Hammersmith home today.

Radiator Installation & Replacement

Most radiators we take off a wall have outlived two or three boilers. The steel panel has thinned, the brackets have worked loose in the plaster, and the copper tails have been reworked by whoever came before. That history decides how the new one goes on.

A radiator replacement is rarely a straight swap. Heights and pipe centres differ from one make to the next, so the tails often need shortening or extending, and the brackets need fixing into sound wall rather than old plug holes. We drain down the circuit, lift off the old unit, then fit and level the new one. After that we refill, bleed it and check every compression joint under pressure before anyone leaves.

Radiator installation in a new position follows the same pattern. Moving a radiator to another wall means running fresh pipework back to the flow and return, routed so it sits tidy along the skirting rather than across the floor.

Every installation is backed by our guarantee of up to 10 years. Our own engineers do the work, so the firm that quotes the job is the firm that fits it. No subcontractors, no handover between strangers.

Fitted once. Fitted properly.

Valves, TRVs, Bleeding and Balancing for Hammersmith Homes

A radiator that is warm at the bottom and cold at the top is holding air. One that is cold all over, with a hot pipe feeding it, usually has a valve problem. Across the houses and flats of Hammersmith, these small parts cause more cold rooms than the radiators themselves.

Thermostatic radiator valves

The TRV pin is often the first thing to fail. It sticks after a summer unused, and the radiator stays cold whatever the head is set to. We free the pin where it will move, or replace the valve body where it will not, and fit a matching lockshield on the return so the pair work together.

Bleeding

A bleed key releases trapped air in a minute. But air that keeps coming back points to a cause: a weeping joint, a pump drawing air in, or corrosion inside the panels. We find that cause, so you are not bleeding the same radiator every fortnight.

Balancing

The radiators closest to the boiler heat first and the far ones lag behind. Balancing sets each lockshield so the flow is shared fairly. We do it with the system running, checking the temperature drop across each radiator until the house warms evenly.

Every room should warm together.

Callout, Availability and Quotes in Hammersmith

A dripping valve tail rarely waits for a convenient week. Neither does a radiator that has just split along a seam. So we keep things simple to arrange.

David heads a team of local heating engineers across Surrey, London and the South East, and there are engineers covering Hammersmith and the surrounding W6 area. Because they work locally rather than crossing the county, they can reach you quickly.

Before any radiator work starts, you get a clear written quote. It sets out exactly what the job includes: draining down, removing the old unit, fitting, refilling, bleeding, balancing and the final pressure check. Valves, brackets and pipework are listed, not tacked on afterwards. The quote settles what is being done and why, in writing, so there are no surprises when the work is finished.

Everything is done in-house, by our own Gas Safe registered engineers. Hotels and hospitality premises are a specialism too, where one cold guest room is a room out of use.

Radiator Types and Upgrades

The radiator under a window is often sized for the room as it once was, before an extension or a knocked-through wall changed it. A unit that cannot heat the space runs flat out and still leaves the corners cold.

Panel radiators

Single, double and convector panels in steel cover most rooms. We size the replacement to the room, its windows and its outside walls, so the output matches the heat the space actually loses.

Designer and column radiators

Vertical and column styles suit narrow walls and rooms where a window takes the usual spot. They need careful bracket fixing, as they carry their weight differently from a standard panel.

Towel rails

A heated towel rail in a bathroom can run on the central heating, or with an element for use in summer. We plumb it into the circuit and set its valves so it warms with the rest of the house.

The right size matters more than style.

Safe Fitting and Heating System Compatibility

Drain an older system and the water often comes out black. That is magnetite sludge, and it settles in the bottom of panels, blocking flow and shortening the life of anything new you fit.

So we check the system before adding to it. A sealed system and an open vented one behave differently, and a new radiator changes the volume of water the boiler has to heat. We match the radiator and its valves to your boiler, check the pressure after refilling, and dose the water with inhibitor to slow corrosion. Where sludge is heavy, a powerflush may be the sensible first step, and we will tell you so plainly.

Any work that touches the boiler or its gas supply is gas work, and the Gas Safe Register requires a registered engineer for it. Ours are registered.

New radiators deserve clean water.

Radiator Repair and Leak Fixing

A green crust around a valve nut means water has been weeping there for months. A brown stain on the carpet below a panel usually means a pinhole in the steel itself. The two need very different fixes.

Many leaks come from the valve, not the radiator. We repack a weeping gland, replace a worn olive on a compression joint, or swap a valve that has corroded through. A panel with pinholes is past repair, so there we fit a replacement, and the installation side of the job carries the same guarantee of up to 10 years.

Where water is escaping somewhere you cannot see, under a floor or behind a boxed-in pipe, we use thermal imaging and acoustic methods to pinpoint it without lifting boards on a guess.

Ring us about the radiator that is leaking, and one of our engineers can usually be with you on the same day. Most radiator repair jobs are put right on that first visit, with the parts carried in the van. From radiator installations & repair in Hammersmith to a gas engineer in Hammersmith, we cover the whole area, with our own engineers and a written quote before any work begins.